嵌縫石膏是由天然或合成的油脂等為基料，同碳酸鈣、滑石粉等礦物摻合，形成高黏度的塑性膏狀物，一般在氧化后表面成膜并隨時間延續氧化深入內部而逐漸硬化。嵌縫石膏具有明顯的塑性，可用手或刮刀嵌填膩縫，成本低，施工方便。

Caulking gypsum is a high viscosity plastic paste made from natural or synthetic fats as the base material, mixed with minerals such as calcium carbonate and talc powder, to form a film on the surface after oxidation and gradually harden over time. Caulking gypsum has obvious plasticity and can be used to fill greasy joints by hand or scraper, with low cost and convenient construction.

嵌縫石膏和膩子的凝結速度和主要作用不同，嵌縫石膏比膩子的凝結速度慢，不容易打磨，通常用來做基層處理，填平裂縫;膩子主要用于普通水泥墻面刷乳膠漆前的打底。

The setting speed and main function of caulking gypsum and putty are different. The setting speed of caulking gypsum is slower than that of putty, and it is not easy to polish. It is usually used for base treatment and filling cracks; Putty is mainly used for priming ordinary cement walls before applying latex paint.

濟南嵌縫石膏的施工方法是怎樣的？

What is the construction method for Jinan caulking gypsum?

1、調配嵌縫石膏

1. Mix caulking gypsum

準備一個干凈的桶和攪拌器，桶里加入適量的水的，然后加入粉放置幾分鐘后攪拌均勻，達到可以施工的粘稠度即可。

Prepare a clean bucket and mixer, add an appropriate amount of water to the bucket, then add powder and let it stand for a few minutes before stirring evenly until the viscosity that can be applied is reached.

2、接縫施工

2. Joint construction

將攪拌好的材料均勻地刮在板縫處，厚度約2mm，將接縫紙帶壓入濕料中，用刮刀或批刀批平。

Evenly scrape the mixed material onto the seam of the board, with a thickness of about 2mm. Press the seam paper strip into the wet material and use a scraper or screwdriver to level it.

3、養護裝飾

3. Maintenance decoration

接縫部位的嵌縫石膏完全干燥后，就可以進行后續的裝飾了。

After the caulking gypsum at the joint is completely dry, subsequent decoration can be carried out.

膩子的施工方法的怎樣的？

What is the construction method for putty?

1、準備工具

1. Prepare tools

膩子施工重要的就是平整均勻，一般會使用到刮板，省時省力，用起來也很方便。

The important thing for putty construction is that it is flat and uniform. Generally, a scraper is used, which saves time and effort, and is also very convenient to use.

2、墻面基層處理

2. Wall base treatment

墻面刮膩子首先要處理基層，如果是老舊的墻面，已經出現起皮、脫落、開裂的情況，要把墻面的墻皮清理干凈，較大的裂縫填補平整，才可以進行后續的膩子施工。

To apply putty on the wall, the first step is to treat the base layer. If an old wall has already peeled, peeled off, or cracked, the wall surface must be cleaned and the larger cracks filled flat before proceeding with subsequent putty construction.

3、膩子粉施工

3. Putty powder construction

在水桶先加適量的水，將膩子倒入桶內，用攪拌器攪拌均勻。然后放置幾分鐘再開始施工，保證膩子和水融合的程度更高。用刮板蘸取膩子直線涂抹或呈扇形弧度刮,用刮板蘸取膩子直線涂抹或呈扇形弧度刮涂，將膩子壓平即可。一般膩子要刮涂兩遍，上一遍干燥后才能進行下一層的刮涂，刮涂兩遍后待膩子晾干，再進行打磨處理，將墻面上不平整的地方打磨平整。

Add an appropriate amount of water to the bucket first, pour the putty into the bucket, and stir evenly with a mixer. Then let it sit for a few minutes before starting construction to ensure a higher degree of fusion between the putty and water. Use a scraper to dip the putty in a straight line or in a fan-shaped arc, then use a scraper to dip the putty in a straight line or in a fan-shaped arc, and press the putty flat. Generally, putty needs to be applied twice, and the previous layer should be dried before the next layer can be applied. After applying twice, the putty should be allowed to dry before polishing to smooth out any uneven areas on the wall.

4、注意事項

4. Precautions

墻面膩子的施工對溫度是有要求的，寒冷的冬季盡量避免施工，會影響施工效果。膩子刮涂完成后，要進行適當養護，短時間內不要碰水。您對此還有什么需求就來我們網站http://www.360orange.cn咨詢吧！

The construction of wall putty has temperature requirements, and construction should be avoided as much as possible in cold winter, as it may affect the construction effect. After the putty is scraped and applied, appropriate curing should be carried out and water should not be touched for a short period of time. If you have any further needs regarding this, please come to our website http://www.360orange.cn Consult!