一、甲醛超標的建議小心點

1、 Be careful when dealing with formaldehyde exceeding the standard

有些膩子粉為了效果好摻入膠水，甲醛超標環保性能不強。所以購買膩子粉先要保持膩子粉的安全性能。膩子粉普遍用于家庭裝修，因為施工簡單方便，所以被很多業主推崇。質量好的膩子粉經過嚴格質量檢測，外包裝有國家認證標識，業主不要為了貪小便宜選擇劣質膩子粉。接下來小卓帶大家了解一下膩子粉如何選購。

Some putty powders are mixed with glue for better results, but their formaldehyde exceeds the standard and their environmental performance is not strong. So when purchasing putty powder, it is necessary to maintain the safety performance of the putty powder first. Putty powder is commonly used for home decoration, and is highly praised by many homeowners due to its simple and convenient construction. High quality putty powder undergoes strict quality testing, and the outer packaging has a national certification mark. Owners should not choose inferior putty powder for the sake of small gains. Next, Xiaozhuo will take you to learn how to choose putty powder.

二、產品有兒童安全級需要仔細選擇喲

2、 The product has a child safety level and needs to be carefully selected

1.在選膩子粉的時候先看包裝，需要注意的是膩子粉的生產標準、生產日期是否存在，選擇標注建材產品兒童安全級的膩子。

When selecting putty powder, first check the packaging, pay attention to whether the production standards and production dates of the putty powder exist, and choose putty labeled with the child safety level of building materials products.

2.從膩子硬度、白度、細度、和易性、施工性能等方面考慮，用肉眼一般很難分辨其好壞。好的膩子粘結強度超國標2倍、粉質細膩，反之，發散、有針孔的膩子質量差，用灰刀鏟一些和好膩子，很快就掉下來的，說明該膩子粘性差，千萬不要選。不然后期墻面開裂、脫落、粉化，煩惱不斷!

2. Considering the hardness, whiteness, fineness, workability, and construction performance of putty, it is generally difficult to distinguish its quality with the naked eye. Good putty has a bonding strength twice that of the national standard and a fine powder texture. On the contrary, putty with divergence and pinholes has poor quality. If some good putty falls off quickly after being scraped with a mortar knife, it indicates that the putty has poor adhesion and should not be selected. Otherwise, the wall will crack, fall off, and powder in the later stage, causing constant troubles!

3.一般的擁有自己獨立品牌的膩子粉都是非常的注重自家的品牌的，基本上都會用防偽標識，刮開涂層聯系即可分辨真假。

3. Generally, putty powders with their own independent brands pay great attention to their own brand, and usually use anti-counterfeiting labels to distinguish between genuine and fake by scraping off the coating.

用膩子的注意事項

Precautions for using putty

1.水和膩子粉的配比，加水量在40%-50%左右。

The ratio of water to putty powder should be around 40% -50%.

2.我們刮的膩子，不是要求光而是在進行找平

2. The putty we apply is not for light, but for leveling

3.涂刷墻面的膩子，一般是要求刮三遍的，但是每一遍的刮膩子都是要求其干了之后再進行下一遍的涂刷。

3. When applying putty to the wall, it is generally required to scrape it three times, but each time the putty is scraped, it is required to dry before applying the next coat.

4.在刮膩子的時候，一定要避免冷風直吹，這樣雖然看似可以把墻面給吹干了，但其實它卻是把墻面的水分給鎖在墻里面了，如果此時進行下一步的操作，等到冬天供暖的時候，原來沒有干的墻面材料就會開始蒸發，出現“干裂”的情況。

4. When scraping putty, it is important to avoid direct cold air blowing. Although this may seem like it can dry the wall, it actually locks the water in the wall. If you proceed to the next step at this time, when winter heating comes, the previously dry wall material will begin to evaporate, resulting in "dry cracking".

5.基層吸收性強時，應在刮涂膩子前用底涂進行封閉，以免膩子中的膠料被基層過多的吸收，影響膩子的附著力。

When the base layer has strong absorption, it should be sealed with a primer before applying putty to prevent the adhesive material in the putty from being absorbed too much by the base layer, which may affect the adhesion of the putty.

6.掌握好刮涂時工具的傾斜度，用力均勻，以保證膩子飽滿。

6. Master the inclination of the tool during scraping and apply even force to ensure that the putty is full.

7.為避免膩子收縮過大，出現開裂和脫落，一次刮涂不要過厚，根據不同膩子的特點，厚度以0.5~1mm為宜

7. To avoid excessive shrinkage, cracking, and detachment of putty, do not apply too thick at once. Depending on the characteristics of different putty, a thickness of 0.5-1mm is recommended

8.不要過多地往返刮涂，以免出現卷皮、脫落或將膩子中的膠料擠出，封住表面不易干燥。

8. Do not apply too much back and forth to avoid rolling, peeling, or squeezing out the adhesive in the putty, which will seal the surface and prevent it from drying out easily.

9.選擇適當的膩子和刮涂工具，用油灰刀填補基層孔洞和裂縫時，食指壓緊刀片，用力將膩子壓進缺陷內，要填滿、填實，將四周的膩子收利刮干凈，使膩子痕跡盡量減少。

9. Choose appropriate putty and scraping tools. When filling the holes and cracks in the base layer with a putty knife, press the blade tightly with your index finger and apply force to press the putty into the defect. Fill and compact the putty, and scrape off the surrounding putty to minimize the putty marks.

選擇質量高的膩子粉，拒絕返工修修補補。

Choose high-quality putty powder and refuse rework and repair.

本文由濟南膩子粉友情奉獻.更多有關的知識請點擊:http://www.360orange.cn我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

This article is a friendly contribution from Jinan Putty Powder For more information, please click: http://www.360orange.cn We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message